02:33
máy tính nguyên vũ
The multichannel input/output terminal is carried and it can develop into a multichannel play by adding power amplifier, such as SM6100SA ver.2.
The capacitor only for an audio is adopted as 17 decoupling capacitors of a pre part and the Power part. Moreover, the newly developed high-quality sound film capacitor is adopted everywhere. Furthermore, the schottky-barrier diode of the low-noise adopted with separate amplifier is used for a power-source block, and low-noise-ization is attained as it is efficient.
Grand potential is improved completely, repeating a tone-quality study, and the shake of potential is suppressed.
A six-channel preamplifier is carried.
Low-noise-izing and a high slew rate are realized by adopting a current feedback type as all the circuitry of six channels, and using a high precision low-noise metal film resistor and a film capacitor.
The motor-drive 6-unit volume of a die-casting frame is adopted as a volume.
From the conventional thing, this volume has little deflection between channels, and has obtained tone-quality performance higher than an electronic volume.
The current feedback type circuitry is adopted as a stereo power amplifier block. The phase compensation was made light by lowering a feedback impedance, and high speed amplifier is realized.
Moreover, in PM8100SA ver.2, parts which carried out with separate amplifier and it had, such as a film capacitor and a resistor, are adopted. Furthermore, the power device has adopted the transistor LAPT for audios excellent in the high region property.
The oscillation and the thermal crosstalk are reduced by making a heat sink on either side become independent.
The super ring-core toroidal transformer with little leakage magnetic flux is adopted as a power-source part. Moreover, the schottky-barrier diode is adopted as a rectifier circuit.
compact disk and the DVD input serve as a direct input design linking directly to a preamplifier part from the input terminal by the exclusive relay.
The speaker terminal made from German WBT is adopted as a speaker termination.
The full REC serector with the Lec buffer is carried.
The double layered chassis is adopted.
The phone equalizer amplifier corresponding to man-month cartridge is carried.
The inlet type AC cable is adopted.
Wireless remote control is attached.
.JPG)
.JPG)
.JPG)
.JPG)
.JPG)
.JPG)
.JPG)
.JPG)
| Form | Integrated Amplifier |
| Output power (20Hz - 20kHz, both channel simultaneous drive) | 90W+90W (4ohms) 75W+75W (6ohms) 60W+60W (8ohms) |
| THD (20Hz - 20kHz, both channel simultaneous drive, 8ohms) | 0.01% |
| Cross modulation distortion (SMPTE) | 0.01% |
| Output bandwidth (an 8-ohm load intensity, 0.04%) | 10Hz - 50kHz |
| Frequency characteristic (compact disk, Source Direct) | 5Hz-70kHz+0 -1 dB |
| Dumping factor (8 ohms, 20Hz - 20kHz) | 100 |
| Input sensitivity/impedance | Phono man month: 2.4mV/47kohm High SFT Level: 210mV/25kohm |
| Phono maximum permissible input (1kHz) | MM:130mV |
| RIAA deflection (20Hz - 20kHz) | ±0.2dB |
| S/N (an IHF A network, input short-circuit) | Phono MM:85dB High Level:110dB |
| Tone control | Bass: ±8dB (100Hz) Treble: ±8dB (10kHz) |
| Input terminal | Line (2ch): Two lines (compact disk, Tuner)
Line (6ch): One line (DVD) micro disk or a tapes system: One line CD-Recordable: 1 line Phono: One line |
| Output-terminal | Pre out (6ch): One line micro disk or a tapes system: One line CD-Recordable: 1 line Speaker: One line Headphone: One line |
| Supply voltage | AC100V, 50Hz/60Hz |
| Power consumption (Electrical Appliance and Material Safety Law) | 160W |
| The maximum Dimensions | Width 440x height 124x depth of 340mm |
| Weight | 9.0kg |
| Adjunct | Wireless remote control AC cable |
Posted in: 
0 nhận xét:
Post a Comment