LUXMAN MS-11 39,800yen(one set, the August, 1980 release)

The bookshelf type speaker system which adopted the multi-vent tuning scheme.

The 20cm cone type Woofer is carried in low-pass.
The aramid cone diaphragm coated [ the special ointment ] with the network of the aramid fiber is adopted as a diaphragm. Moreover, an aramid is adopted also as a damper and it fabricates with high precision, and also the frame part is made into the open structure in order to avoid a harmful air distortion produced on a damper back side.
The ferrite magnet of 110phimm is adopted as a magnetic circuit, and the heat-resistant high nomex is adopted as a voice coil bobbin. Furthermore, aluminum die-casting is adopted as a frame and the polyurethane form is adopted as an edge.

The 2.5cm dome shape tweeter is carried in the high region.
The polyesters cross is used for the diaphragm of this unit. This diaphragm has newly developed matrix cross structure, and rigidity is secured by making a shaping agent every impregnate beforehand of a fiber. It is not necessary to apply a shaping agent to the network currently performed conventionally by this, or to make glass wool touch a diaphragm rear view for reinforcement.

The network part has set up the point most effective for a reduction of the phase distortion generated near a crossover point.

The multi-vent tuning scheme is adopted as an enclosure.
By this scheme, the enclosure has a structure which opened two or more small holes based on the sealing structure, and has controlled internal air pressure by this hole. This stops the superfluous pressure to the diaphragm which poses a problem with a sealing structure, and also the characteristic peculiarity which poses a problem by a bass-reflex scheme is also suppressed. 

Scheme	2 way and 2 speaker multi-vent tuning scheme - Bookshelf type
Unit	For inside low-pass: 20cm cone type For high regions: 2.5cm dome shape
Frequency characteristic	50Hz - 20kHz
The maximum input	60W
Rated input	25W
Output sound pressure level	89dB/W/m
Impedance	6ohms
Cross over frequency	3kHz.
Dimensions	Width 250x height 540x depth of 255mm
Weight	8.6kg

Read more »

LUXMAN LX55 29,500yen(one set, the November, 1972 release)

The speaker system which miniaturized LX77 further and pursued the quality of sound.

The high compliance type unit of 25cm aperture is adopted as low-pass, and the long voice coil etc. has realized the firm light bass.

A 4cm dome shape unit is adopted as a mid range.
In this unit, while improving a directivity, the modification of a transient and a distorted property is aimed at by suppressing the splitting oscillation with an audio frequency band.
Moreover, it has tied to the bass region smoothly by having lowered fo to the edge sharply by adopting the thing made of cloth, and also carrying out a meltdown.

The direct ring type of the Lux scheme of 3.3cm aperture is adopted as the high region.
This tweeter drives away a splitting oscillation out of an audio frequency band, carries out only a perfect inertia control span, has it, and lengthens a frequency response for a flat to 22000Hz.
The directivity is also the fully examined diaphragm form and the thing which was excellent with the effect of the equalizer.

The network is made into -12 dB/oct.
Moreover, in order to carry out the work united with the impedance characteristic of the speaker unit, for example, to improve relation of a Woofer and a squawker,In order to solve the influence which it has on the peek of the shoulder property by the side of a low cut of the mid range which appears in a speaker load intensity, or the property of fo of a squawker, a network with a peculiar circuitry routing is adopted and relation of sound is made smooth.

Lauan plywood is adopted as an enclosure, the thing of 25mm thickness is used for a top plate and a lower board, and the thing of 18mm thickness is used for the front and the rear 、 sub-.
Reinforcement was put into a front and the back at T character type, it let the reinforcement stick pass on the sub-, the harmful vibration is prevented, and finish is the Shiraki finish.
Moreover, the bond acetate fiber which was excellent in the sound-absorption effect was fully put into acoustic material, and while dumping low-pass, the occurrence of the stationary wave is prevented. 

Scheme	3 ways, 3 speakers, a sealing scheme, and a bookshelf type
Unit	For low-pass: 25cm cone type For mid ranges: 4cm dome shape For high regions: 3.3cm ring type
Frequency characteristic	35Hz - 22000Hz
The minimum resonance frequency	58Hz
Rated input	20W
The maximum input	40W
Impedance	8ohms
Cross over frequency	800Hz, 5000Hz (-18 dB/oct)
Level control	The object for Mid, for High: Coil tap type
Enclosure internal volume	41L
Dimensions	Width 320x height 665x depth of 300mm
Weight	14.5kg

Read more »

LUXMAN L-5 89,800yen(September, 1978 release)

The Integrated Amplifier which investigated the quality of all fields, such as a performance side, an organization side, a functional side, and a design side, and was developed.

The power amplifier part has adopted DC amplifier stream composition which removed the time constant circuitry in the NFB loop which is one of the causes which worsens a transient response. Moreover, about the problem of the drift over a variation of external requirements, such as supply voltage and a temperature, for every main point, an electric and an organization device are given and are suppressed on the level which can be disregarded.
To the power transistor, the destructive-proof intensity selected carefully highly what has high high region cut-off frequency, and EBT (emitter ballast and transistor) is adopted as a driver transistor. Furthermore, the stable high region property with little notching distortion is realized for the pre-driver stage a constant voltage and by carrying out a constant current drive.

The three-step hardwired-connection equalizer circuitry, the two-step hardwired-connection flat amplifier circuitry, and the two-step hardwired-connection tone amplifier circuitry are adopted as a preamplifier part.
In order to attain further more much more low-distortion-izing and high SN ratio-ization, while carrying out the careful selection using of the super-low-noise type with few collector output capacitances with a linear region improve a circuitry fundamentally and large to a using transistor, and high and high region cut-off frequency,It drives with a negative power source, the electric current of many of Japanese predefinedpredefineds is further sent through each circuitry, and low impedance-ization is attained.

The large-sized Troy Dahl power transformer is adopted as a power-source part.
Moreover, a preamplifier part, the predrive stage, and the power stage are another formulated, the efficiency ratio of a power source is raised, and the improvement in a distortion property is aimed at.

In order to advance positively shortest-distance-izing from each input terminal to an amplifier circuitry, and exclusion of shielding wire and to aim at the improvement in a performance, it is dared to form the input terminal plate in the bottom.

the LUX scheme NF type is adopted as a tone control, and also the object for high regions and the method of low-pass have prepared the curving point frequency switchover 2 points every. A defeet is also possible for this tone control.
In others, filter circuits, such as a Subsonic Filter, a low cut-off filter, and a high cut-off filter, a monitor & dubbing functionality, a speaker selector, a loudness control, -20dB audio Attenuator, etc. are carried.

A separation using of a preamplifier part and a power amplifier part is possible. 

Read more »

LUXMAN L-3 59,800yen(October, 1978 release)

The Integrated Amplifier which pursued the tone quality at the time of Loule Bell by the low power output.

The pure complimentary OCL scheme is adopted as a power amplifier part, and also the element itself, such as a power transistor, is fully examined,While especially a high region barrier property selects carefully and uses what has a high and few collector output capacitance, the operating point is set as a fraction with the sufficient linearity of each transistor, and the modification of a distortion property covering all the bands is aimed at.

A two-step direct coupling system is adopted as the equalizer circuitry of a preamplifier part, a flat amplifier circuitry, and a tone amplifier circuitry, the electric current sent through each circuitry is increased, low impedance-ization is attained, and the modification of a high region property is aimed at.
Furthermore, the modification of the SN ratio is aimed at by selecting carefully and using the super-low-noise type for a transistor, if a circuitry is constituted, and also driving with a negative power source.

In order to perform shortest-distance-izing of each input system, and exclusion of shielding wire, it is the layout which formed the input terminal plate in the bottom.
Moreover, the simplification of a signal path is attained and a flat property and high SN ratio-ization are attained.

Functionalities, such as a LUX scheme NF type tone control, a monitor & dubbing functionality with two tape decks, height each filter, and a loudness control, are carried. 

Form	Integrated amplifier
Succession effective output (both channel operation)	35W+35W (8 ohms, 20Hz - 20kHz)
THD (20Hz - 20kHz)	0.04% or less (8ohm, 35W)
Cross modulation distortion (60Hz:7kHz=4:1)	0.08% or less (8ohm, 35W)
Output bandwidth	10Hz - -60kHz three dB (0.1% of distortion)
Frequency characteristic	60kHz [ 15Hz - ]-less than 1dB
Input sensitivity/impedance	Phono: 2.5mV/50kohm Tuner, Aux:145mV/50kohm
SN ratio (an IHF-A correction, input short-circuit)	Phono: 72dB or more Tuner, Aux: 95dB or more
Dumping factor	65 (an 8-ohm load intensity, 1kHz) or more
Tone control	LUX scheme NF type (the right and left ch, independent level control)
Filter	Subsonic speed: 25Hz-6dB / oct A high cut: 7kHz-6dB / oct
Attachment	Tapes monitor circuitry (two lines) Tapes dubbing circuitry Loudness control Speaker selector (two lines) Mode switch
AC outlet	Power-switch interlock: One line Power-switch un-interlocking.: One line
Supply voltage	AC100V, 50Hz/60Hz
Power consumption (Electrical Appliance and Material Control Law)	100W
Dimensions	Width 438x height 105x depth of 313mm
Weight	8kg

Read more »

LUXMAN MS-10 38,100yen(one set, the March, 1979 release)

　
The speaker system of aramid fiber adoption which started with the development of unit each and was developed over five years of time.

C2038K which is a 20cm cone type Woofer is carried in low-pass.
The aramid fiber system plastics cone which consists of two or more kinds of quality of a composite material was adopted as the diaphragm of this unit, the science treatment was performed to the mesh-like material (aramid fiber), and the diaphragm excellent in a light weight and rigidity is realized by carrying out heating molding. Moreover, the same material as a cone was adopted also as the damper, and the outstanding flattery nature and responsibility, and controllability have been acquired.
In consideration of the Tran Gent property, the polyurethane form was adopted as the edge and high compliance and low fo are realized on it.
Moreover, bar arm type aluminum die-casting is adopted as a frame, and also in order to reduce air distortion produced on the back side of a damper, a work, such as vacating an air hole, is carried out.

D2501F which is a 2.5cm dome shape tweeter is carried in the high region.
The dome shape diaphragm completed based on the polyester film is adopted as a diaphragm, and relation of sound is made more smooth by using the material of a plastics system homogeneous as a low-pass unit.
Furthermore, the large-sized ferrite magnet with the outer diameter of 70mm, a bore of 36mm, and a thickness of 30mm was adopted as the magnet, and the flux density of 11,000gauss is secured. Moreover, big power handling and capacity have been obtained by adopting a nomex as bobbin material.

The lowpass and high-pass side is designed by -18 dB/oct., and also the network part is designed perform the drive according to the rate of change of each unit in order to make it operate ideally as a filter. Moreover, in order to lessen the interference between units, the corrective network was prepared, and the occurrence of the masking effect near a cross over frequency is prevented.
What was examined also for the material was used, the low-loss type with little direct current resistance in a coil was adopted, and the metallized film type is adopted as a capacitor.

The multi-vent tuning scheme is adopted as the design of an enclosure. On the basis of the enclosure of closed mold, this opened two or more small holes in the rear surface of a box, is a scheme which reduces the air pressure in a box in the suitable status, and has acquired the strength of a sealing scheme and a bass-reflex scheme. By this, it was lost that it is under many pressures to a cone, and the outstanding property has been acquired.
High damped hard particle board is adopted as the quality of the material, inside, the sound-absorption effect is high, the super seal which can suppress an oscillation of particle board effectively is stuck, and the unnecessary radiation from an enclosure is reduced.

Reliability is high to a speaker terminal area, and the lead it1 type terminal which is easy to use is adopted as it. 

Read more »